The Jewell Instruments model DMH is a high precision MEMS inclinometer. Units are available with RS-232, RS-422, RS-485 and UART TTL options. All DMH series inclinometers are rated IP67 for waterproofing up to 1m. Custom ranges and output types are also available on request.
The Jewell Instruments model DML is a low cost digital MEMS inclinometer for industrial applications. Units are available with RS-232, RS-485 and UART TTL output options. All DML series inclinometers are rated IP67 for waterproofing up to 1m. Custom ranges and output types are also available on request.
The model DMS is a mid-level performance digital MEMS inclinometer for industrial applications. Standard units are available in RS-232, RS-485 and UART TTL interface options. All DMS series inclinometers are rated IP67 for waterproofing up to 1m. Custom ranges and output types are also available on request.
The ECS digital compass represents the state-of-the-art in magnetic compassing. It combines a precision 3-axis solid-state magnetometer and a rugged 2-axis electrolytic tilt sensor to provide accurate heading and tilt measurements over a wide range of environmental conditions. The firmware and signal processing algorithms have been refined and improved over three prior generations of compasses to deliver the ultimate in performance from the available sensor data.
The ECV eCompass Series is a 3D electronic compass providing stable azimuth, pitch, and roll measurements in dynamic conditions. As an enhanced version of our ECG Series, the ECV includes a full suite of precision, 3-axis, MEMS sensors, and an optional dual-axis electrolytic tilt sensor, for the ultimate in near-level accuracy. A high-performance microcontroller orchestrates the fast measurement sequence, sensor calibration adjustments, frame-of-reference translations, trigonometric calculations, and advanced signal processing required to provide accurate heading, pitch, and roll outputs.
Jewell Instruments’ offers ECV-IMU Series initial measurement units which assure high accuracy in a small package. This inertial measurement unit is a cost efficient, low power consuming device which provides stable azimuth, pitch, and roll measurements in dynamic conditions. This sensor consists of 3-axis angular rate gyros, 3-axis accelerometer, 3-axis magnetometer, and optional 2-axis electrolytic tilt sensor. These IMUs have a wide operating range and are factory calibrated. Hence, they offer an accurate and fast output through RS-485.
The IRIS-SC digital signal conditioning card is a powerful control device designed for use with all Jewell miniature tilt sensors. Output is ASCII RS-232 or RS-422(485) serial. Standard firmware includes five user-programmable alarm/trigger thresholds for tilts tilt switch/control applications. When a selected threshold is reached, the circuitry sets the output high
on one of the pins in the H3 control connector. Other firmware features include user-programmable data output rates, sample averaging, autozero (nulling), and baud rate. The IRIS-SC can also log up to 22,000 samples to internal memory for data dump/download on user command.
All IRIS-SC units include calibration when ordered with Jewell miniature tilt sensors (specify calibrated range on order).
The Model 701-2 Platform mount tiltmeter is our most popular design for high precision tilt measurements. Units come with built-in invar leveling legs, for easy installation on any horizontal surface. The A701-2 also includes two switchable gains and two low-pass filter settings. Using an absolute gravity-referenced electrolytic sensor, the A701 delivers ultra-high sensitivity to <0.1 µrad with virtually zero long-term drift. The output is a stable ±8 DC voltage (±16 VDC differential). The D701 digital version has onboard memory, with a storage capacity of up to 22,000 samples.
The Model 801 “Tuff Tilt” Tiltmeter series combines high precision and durability in an economical instrument package. Using an absolute gravity referenced electrolytic sensor, the 801 series delivers superior measurement accuracy with virtually no long-term drift. Units are available in a variety of configurations including single axis (uniaxial), or dual axis (biaxial), analog, digital, or 4-20mA outputs.
All units are rated IP65 waterproof for advanced protection from the elements.
The Model 802 DeepWater Series is the fully submersible cousin of our Model 801 Tuff Tilt Series. Performance features are the same, but the DeepWater housing is machined from a solid piece of 316 stainless steel and incorporates a high-pressure neoprene connector. The pressure rating is 250 bars (2500 meters depth). Higher-pressure versions may be special ordered. Temperature rating is governed by the neoprene connector. Wider temperature range is available with other connector types. Units are available in a variety of configurations including single axis (uniaxial), or dual-axis (biaxial), analog, digital, or 4-20mA outputs.
The model 875 Mini “Tuff Tilt” Tiltmeter combines high precision and durability in a miniaturized and economical instrument package. Using MEMS technology, the 875 delivers superior measurement accuracy with virtually no long-term drift and a resolution of 0.05°. Output options include 0.5-4.5Vdc, 4-20mA and digital RS-485. All units are rated IP67 waterproof for advanced protection from the elements. Use the 875 Mini “Tuff Tilt” for structural monitoring, angle measurement, and control, platform leveling, testing and research, OEM, and more.
The biaxial model MD900-T is an economical digital clinometer with powerful firmware features. User programmable settings include AUTO-zero (tare), baud and output rate, sample averaging, and more. Output is RS-232 or RS-422 (RS-485 full-duplex). The MD900-T easily integrates with a variety of GPS receivers and supports Trimble TCM, NMEA XDR, BAE, and Ashtech output protocols. Units ship standard with 6-ft. hook-up cable and a 100-240VAC power transformer. Use the MD900T for industrial pitch and roll measurement, marine piling, dredging and construction systems, platform leveling, geotechnical monitoring, and more.
The IRIS Tilt Switch and Controller is a powerful tilt controller device that combines a digital, dual-axis clinometer and advanced firmware features in one compact unit. This remarkable instrument enables you to measure and respond to rotational movements in any direction concerning the unchanging gravity vector. Units ship standard with a 24-inch hook-up cable. IRIS is an ideal choice for OEM applications, where it can be used to maintain platform levelness, avoid tip-over conditions, prevent out-of-range movement, and perform other control functions.