Jewell DG Series - Moving Coil & Rectifier 90° Scale
Jewell DG Series - Moving Coil & Rectifier 90° Scale

Jewell DG Series – Moving Coil & Rectifier 90° Scale

Highlights:

The moving coil, rectifier meters, DG 48/72/96/144 are housed in molded polycarbonate cases and are suitable for the measurement of AC currents and voltages. Moving coil rectifier instruments measure average values and are calibrated to indicate RMS values, assuming a sinusoidal waveform for frequencies from 40 to 10000 Hz (AC current for frequency range of 40 to 1000 Hz and AC voltage for frequency range of 40 to 1000 Hz. These instruments offer several advantages in switchboards and generating set panels. A number of meters can be mounted in a panel cut-out (mosaic mounting). Front glass, bezel & dial can easily be replaced

Compare
Categories: , Tags: , , , , , , , , ,
Additional information
Features

• Less VA burden
• Linear Scale
• Glass-filled polycarbonate housing (UL 94-V-0)
• Knife-edge pointer
• Easily replicable glass and bezel
Movement

Moving coil movement has pivots of very high hardness. Movement is suspended between spring-loaded sapphire jewels. Movement is properly shielded and critically damped by eddy currents induced in coil former.
Case Options

• Antiglare glass front fascia
• Red, yellow, blue, or white bezel color
• Front adjustable on-site red index pointer
• 15° to 165°C position of use available on request
Dial Options

• Blank dial with initial and end values marked
• Number or letter markings
• Basic divisions without numbering
• Red or green markings or bands
Specifications

Specifications

Mechanical

Case DetailsMolded square suitable for mounting in control switchgear panels and machinery consoles.
Case MaterialPolycarbonate, flame retardant, and drip-proof per UL 94-V-0
Front FasciaGlass
Color of BezelBlack
Position of UseVertical
Panel FixingMounting clamps
MountingStackable in a single cutout
Panel Thickness≤1.5mm
TerminalsVoltmeters & Ammeters <6A: Hexagon studs, M4 screws and wire clamps, E3 (DIN 46282).
Ammeters ≥6A: Threaded stud- M6 with nuts.

Electrical

Measured QuantityAC voltage or current
Overload CapacityAcc to IS: 1248/IEC 51
Continuously1.2 times rated voltage/current
Short Duration2 times rated voltage, 5 seconds maximum
10 times rated voltage, 5 seconds maximum
Enclosure Code (IEC 529)IP 52 - case cover
IP00 - terminals without back cover
IP20 - terminals with back cover
Insulation ClassGroup A according to VDE 0110
Rated Insulation VoltageDG48: 660V
DG72 & DS96: 1000V
Proof VoltageDG48: 2kV
DG72 & DG96: 3kV
Insulation Resistance<50MΩ at 500 Vdc

Scale & Pointer

ModelDG48DG72DG96DG144
Scale Length41mm61mm97mm146mm
Scale CharacteristicsLinear*
Scale DivisionCoarse - Fine
Scale InterchangeabilityInterchangeable*
PointerKnife edge
Pointer Deflection0-90°

*Scale are nonlinear and not interchangeable for ammeters <750mA

Environmenal

Climatic SuitabilityClimate category II as per IS:1248, IEC 60051
Climatic class III according to VDE/VDI 3540
Operating Temperature-10° to +55°C
Storage Temperature-25° to +65°C
Relative Humidity≥75% annual average, non-condensing
Shock Resistance15gn for pulse duration 11ms
Vibration Resistance10-55-10 Hz for amplification 0.15mm (1.5g at 50Hz)

Applicable Standards

Applicable Standards

IS 2419
DIN IEC 61554		Nominal case and cutout dimensions for indicating electrical instruments
IS 1248Scale and pointer for electrical measuring instruments
IS 1248Connections and terminal markings for panel meters
DIN 46200
DIN 46282		Terminal bolts/leads
VDE 0110
VDE 0410
IEC 529
IEC 1010		Safety requirements and protective measures for electrical indicating instruments and their accessories.
IS 1248
IEC 51/DIN EN 60051
DIN 43701		Performance specifications for direct acting indicating analog electrical measuring instruments and their accessories.
IS 1248
IS 9000
VDE/VDI 3540		Environmental condition
DIN 43718Front frames for indicating measuring instruments principle dimensions
UL 94-V-0UL combustibility class
DIN 43701Technical conditions of delivery for electrical instruments
IS 1248/IEC 51
IS 9000
VDE 0411
IEC 1010		Mechanical strength (free-fall test, vibration test)
Downloads

Downloads

Datasheet

Related Products

Model 711-2 & A716-2

Highlights:

The models A711-2 (floor-mount), and A716-2 (wall-mount) bolt or clamp to any surface, and are well suited for areas with heavy traffic or vibration. Electronic performance is identical to the model A701-2. Floor-mount models are available with a weatherproof NEMA 4X seal (A711-2 4X), or with an RS-232, RS-422, or RS-485 digital output (D711). D711 units also include onboard memory with a storage capacity of up to 22,000 samples. Units include two switchable gains and two low-pass filter settings and are sensitive to <0.1 µrad. Applications include volcano monitoring, high-precision geotechnical engineering, bridge deflection monitoring, precision metrology, radar platform leveling, and high-accuracy tilt monitoring applications where bolt-on installations are required.

Compare
Jewell DSL Series – DC Ammeters/Voltmeters

Jewell DSL Series – DC Ammeters/Voltmeters

Highlights:

The moving coil panel meters, DSL 48/72/96/144 are housed in molded polycarbonate cases are suitable for the measurement of DC currents and voltages. These instruments offer several advantages in switchboards and generating set panels. A number of meters can be mounted in a panel cut out (mosaic mounting). The front glass, bezel, and dial can be easily replaced.

Compare
A&M 2.5 Square Ruggedized Series

A&M 2.5 Square Ruggedized Series

Highlights:

Designed and manufactured in conformance with MIL-PRF-10304 (not QPL listed). Ideal for communication or test equipment where severe environmental conditions are encountered. Available size 2.5″.

Compare
Modutec PB Series Surface Mount Panel Meters

Modutec PB Series Surface Mount Panel Meters

Highlights:

The PB Series was designed to meet the expressed need of many customers for meters with a hard-hitting, big-dial area “industrial” look.

PB Series meters are available in many sizes, types, and ranges. Mounting stud configuration complies with ANSI standards: the number of studs is as follows: 1½” meters – 2 studs; 2½” & 3½” meters – 3 studs; 4½” meters – 4 studs. Meters in sizes 1½”, 2½”, and 3½” can be supplied in 4- stud versions at no extra cost.

AC meters in this series are offered in both d’Arsonval (rectifier type) and iron-vane versions. The latter has the virtue of greater standard accuracy and relative insensitivity to input distortion, while the rectifier type is less affected by frequency variations.

Compare
A&M MR Panel Meter Ruggedized Series

A&M MR Ruggedized Series

Highlights:

Designed and manufactured in conformance with MIL-PRF-10304 (not QPL listed). Ideal for communication or test equipment where severe environmental conditions are encountered. MR34 Long-scale panel meters are ideal for military and commercial applications. Available 1.5″ (MR13), 2.5″ (MR26) and 3.5″ (MR34 & MR35)sizes.

Compare
Jewell DGL Series – AC Ammeters/Voltmeters

Jewell DGL Series – AC Ammeters/Voltmeters

Highlights:

The moving coil, rectifier panel meters DGL 48/72/96/144 are housed in polycarbonate cases and are suitable for the measurement of AC currents and voltages. Moving coil rectifier instruments measure average values and are calibrated to indicate RMS values, assuming a sinusoidal waveform for frequencies from 40 to 10000 Hz (AC current – 40 to 1000 Hz and AC Voltage – 40 to 10000 Hz). These instruments offer several advantages in switchboards and generating set panels. A number of meters can be mounted in a panel cutout (mosaic mounting). The front glass, bezel, and dial can be easily replaced.

Compare
Modutec E-Series 2? Edgewise Panel Meters

Modutec E-Series 2″ Edgewise Panel Meters

Highlights:

Compact edgewise meter only ½” thick. Self-shielding allows users to stack without magnetic interaction. Lightwell provided for backlighting. Available size 2″.

Compare
Jewell surface mounted 50 series analog panel meter

Jewell 50 Series

Highlights:

The Jewell surface mounted 50 series analog panel meter is designed with traditional black case and glass windows. Black phenolic Bakelite covers and cases suited for industrial equipment. Available in both round and square shapes.

Compare

AMS Analog MEMS Inclinometer Series

Highlights:

The Jewell Instruments model AMS is a mid-level performance analog MEMS inclinometer for industrial applications. Standard units are available with 0-5V, 0.5-4.5V and 4-20mA output options. All AMS series inclinometers are rated IP67 waterproof up to 1m. Custom ranges and output types are also available on request.

Compare
Modutec World Meter Series – Windo-Mount™ Panel Meters

Modutec World Meter Series – Windo-Mount™ Panel Meters

Highlights:

The World Meters incorporate Modutec’s third-generation taut-band/moving-coil movement – unmatched in any competitive production meter, anywhere – with a space-efficient case and dial configuration that takes about 30% less space than conventional panel meters. The result is a rugged and accurate meter with unique and desirable features, at a very economical price.

Compare
Model A800P Portable Tiltmeter

Model A800P Portable Tiltmeter

Highlights:

The Model 800P Portable Tiltmeter is a versatile and accurate hand-held instrument for monitoring structural and foundation movement. Measurements are taken from tilt plates that have been cemented or bolted to any horizontal or vertical surface. Indexing bars on the bottom and sides of the tiltmeter enable you to reposition it accurately on the tilt plate, every time. When continuous monitoring is not required, Model 800P is an excellent choice because only one tiltmeter is needed to make measurements at an unlimited number of points.

The Portable Tiltmeter System includes one tiltmeter, one power and display unit, and a tough plastic carrying case. Ceramic or Aluminum Tilt plates are purchased separately.

Compare
Modutec MD & ME Series Edgewise Panel Meters

Modutec MD & ME Series Edgewise Panel Meters

Highlights:

Useful space-saving meters in two sizes, interchangeable with many costly d’Arsonval meters or moving magnet meters from other sources. All sizes feature flush-to-panel covers without the bulge that disfigures many edgewise meters. A low-cost option provides internal illumination through a translucent dial – sophisticated lighting unusual in any economy meter, let alone an edgewise type.

Compare

Scroll To Top
Close
Close
Shop
Close

My Cart

Shopping cart is empty!

Continue Shopping